FAQ - Technical

Here are some questions on technical topics:

Difference between Mono and Dual Submersible Pumps?

Difference between Mono and Dual Submersible Pumps

Our patent-pending¹⁾ Dual Submersible Pumps (with two connections) offer unprecedented flexibility compared to Mono Submersible Pumps (with one connection). The Dual Submersible Pumps can replicate all performance curves of 2", 3", 4", and 5" Mono Submersible Pumps. The second hose connection on the Dual Submersible Pump allows for doubling the pumping capacity. Additionally, up to 14 combinations of different hose diameters (2", 3", 4", or 5") are possible. The result is an impressive capacity of up to 126 liters per second (l/s) at a weight of only 29 kg (63.9 lbs).

Only in confined spaces would you need to rely on 2" or 3" Mono Submersible Pumps. Otherwise, the Dual Submersible Pump is always the optimal choice. It can also be used as a Mono Submersible Pump and covers a range equivalent to up to eight Mono Submersible Pumps.

Patent-pending Country	Patent Number
Switzerland	CH000493/2023
Europe	24174242.8
USA	18/658467

How do I set the submersible pump to optimal performance?

Oil Flow Optimization

Our submersible pumps can be set to the maximum possible performance. All our submersible pump systems come with an oil pressure gauge. Using this gauge, you can precisely adjust the pump performance to the maximum possible by simply adjusting the oil flow.

Piping

The following diagrams start with minimum piping standards (Diagram 1) using rigid pipes and end with optimal piping (Diagram 4).

Poor Performance (Diagram 1)

Rigid pipes.
Hose end at the highest point.
Result: Worst performance, highest costs.

Good Performance (Diagram 2)

Rigid pipes.
Hose end above hose inlet but below the highest point.
Result: Good performance, high costs.

Better performance with optimized piping

Better Performance (Diagram 3)

Rigid pipes.
Hose end and hose inlet at the same height.
Result: Better performance, lower costs.

Best Performance (Diagram 4)

Rigid pipes.
Hose end below hose inlet.
Result: Best performance, lowest costs.

Can I continue using my existing hoses?

Yes. You can continue using all your hoses. Since the submersible pumps' performance can be adjusted gradually, it is possible to use a 2-inch hose with a 5-inch submersible pump. In short, our submersible pumps can be adapted to your existing hoses.

Which submersible pump sets are ideal for flood protection in firefighting and disaster management?

5-inch Dual Submersible Pumps, combined with petrol or electric units with adjustable oil flow, are ideal. You can connect hoses starting from 2 inches, including A, B, C, and F (5") hoses. In dual operation, up to 112 l/s – 6,666 liters per minute or 400 m³/hour – is possible, making them the first choice when high pump volume is needed. Under practical conditions, up to 88 l/s can be achieved with A hoses (4").

5-inch submersible pump petrol model 23 HP - 40 l.p.m. (20-40 l.p.m.)
5-inch submersible pump electric model with frequency control 18 kW - 40 l.p.m. (adjustable 0-40 l.p.m.)

Are the submersible pumps available with floats?

Yes.
All electric models can be equipped with a float for automatic pump start/stop.
All electric models can also be operated continuously (24/7). All pumps are 100% dry-running capable.

Can submersible pumps be connected in series?

Yes.
Series connection allows pumping over extreme height differences and distances.

What are the advantages of parallel operation?

Parallel operation (simultaneous operation of multiple submersible pumps) offers several advantages:

Theoretically unlimited performance increase.
Cost savings by using only the necessary number of pumps.
Active water management, where wastewater from each pump can be directed to different destinations.
Using inexpensive standard hoses for large pumping capacities (e.g., distributing the water of a 55kW installation across 5 x 4" hoses instead of one 8" hose).
Multiple safety layers against failure: If one of five pumps fails, the remaining pumps continue working.
Positioning pumps at different heights reduces energy and noise levels, as only one pump operates in suction mode, while others run at full capacity or in energy-saving dry mode.

Are the submersible pumps capable of shallow suction?

Yes.
All submersible pumps feature an open inlet at the suction opening. The water level is reduced to a few centimeters, down to the inlet height.
The suction height can be adjusted to any desired level, and the bolts on the open inlet can be customized based on customer needs. The standard spacing for 5" models is 15mm and 102mm.

Can the pumps be used as A-, B-, or C-hose pumps?

The 2", 3", 4", and 5" submersible pumps correspond to "2 inch = C-hose pump", "3 inch = B-hose pump", "4 inch = A-hose pump", and "5 inch = F-hose pump".

FAQ - Commercial

Here are some questions related to commercial topics.

Cost Comparison: Dual vs. Mono Submersible Pump?

Cost Comparison: Dual vs. Mono Submersible Pump

The Dual Submersible Pump reduces water management costs to an unprecedented extent compared to Mono Submersible Pumps. Both in terms of purchase, amortization, and operating costs, our patent-pending¹⁾ Dual Submersible Pump is unbeatable. Submersible pumps with 126 l/s capacity are significantly more expensive to purchase and can weigh several hundred kilos up to a ton, whereas our Dual Submersible Pump weighs only 29 kg (63.9 lbs).
By renting, you can see for yourself how the Dual Submersible Pump is the most cost-efficient and high-performance solution for your water management needs.

⁽¹⁾Patent-pending Country	Patent Number
⁽¹⁾Switzerland	CH000493/2023
⁽¹⁾Europe	24174242.8
⁽¹⁾USA	18/658467

Is the rental cost credited toward the purchase price?

Yes.

What is the lifespan of a submersible pump?

Up to 15 years or more!

Depending on the pump medium, the submersible pump head lasts more than 15 years without major repairs.
The same applies to the hydraulic units.
This is partly due to the minimized wear on all mechanical parts by the hydraulic oil and the integrated safety shutdowns in the unit.
These reliably prevent damage to the pump motor and unit motor in case of impeller blockage due to solid materials.

⁽¹⁾Patent Pending Country	Patent No.
⁽¹⁾Switzerland Pat. No.	CH000493/2023
⁽¹⁾Europe Pat. No.	24174242.8
⁽¹⁾USA Pat. No.	18/658467

⁽¹⁾Patent Pending Country

Patent No.

⁽¹⁾Switzerland Pat. No.

CH000493/2023

⁽¹⁾Europe Pat. No.

24174242.8

⁽¹⁾USA Pat. No.

18/658467

⁽¹⁾Patent Pending Country

Patent No.

⁽¹⁾Switzerland

CH000493/2023

⁽¹⁾Europe

24174242.8

⁽¹⁾USA

18/658467

⁽¹⁾Patent angemeldet Land	Patent Nr.
⁽¹⁾Schweiz Pat.-Nr.	CH000493/2023
⁽¹⁾Europa Pat.-Nr.	24174242.8
⁽¹⁾USA Pat.-Nr.	18/658467

⁽¹⁾Patent angemeldet Land

Patent Nr.

⁽¹⁾Schweiz Pat.-Nr.

CH000493/2023

⁽¹⁾Europa Pat.-Nr.

24174242.8

⁽¹⁾USA Pat.-Nr.

18/658467

Hydraulic Submersible Pumps up to 126 l/s (2,000 USGPM)

We have the right submersible pump for you if:

You want to pump sewage or wastewater. Your pumps must run continuously dry. You need a mobile, modular, and scalable solution for heavy rainfall events and flooding. You require cost-efficient solutions for water management in the area of sewer rehabilitation or treatment plants. You need complex water management in continuous operation 24/7 and 365 days a year. You are looking for a pump for suction operation in silent mode. You want to save the costs for E-Check. You want to reliably avoid cavitation damage. You are looking for a slurry pump. You want to pump bentonite. Your pumping medium contains large solid particles up to 74 mm (2.9 inches). You are looking for a pump with integrated grinding and mixing function for pumping solids. You need an explosion-proof (ATEX) pump. Your pumping medium reaches up to 80°C (176°F). You require 100% protection against electric shock. You need a pump system for extreme height and extreme volume. You are looking for pumps that can handle 50 m³/hour (13,208 USGPH) with 7 kg (15 lbs) weight, and up to 400 m³/hour (105,669 USGPH) with just 29 kg (64 lbs). You need pumps for passages with diameters less than 24 cm (9.4 inches). You want flexibility to switch between electric, gasoline, or diesel power. You need submersible pumps with continuously adjustable pump output. You want to continue using your existing hoses. You are looking for pumps with the lowest lifetime costs on the market.

Infographics for 2", 3", 4", and 5" Mono-/Dual Submersible Pumps

Youtube

Youtube

FAQ

Downloads

Performance Curves PDF for All Models

4 Hydraulic Submersible Pump Heads

- the cost-efficient submersible pump solution -

All four submersible pumps are hydraulically operated. The flow rate can be continuously adjusted by controlling the oil volume. The oil supply can be provided by either a vehicle hydraulic system or a hydraulic power unit.

Up to 50 liters per minute (13 USGPM) of oil flow at up to 250 bar pressure (3,625 psi) can be used to operate the submersible pumps.

Stay flexible. Depending on the requirement, you can alternately operate the pump head with electric, gasoline, or diesel motors.

The dual submersible pump head is the all-rounder solution.

The dual submersible pump head combines the advantages of 2", 3", 4", and 5" submersible pumps. With the appropriate adapters, up to two hoses can be connected simultaneously. This results in an unprecedented pump output. In dual mode, two 2-inch, or two 3-inch, or three 4-inch, or two 5-inch hoses can be used. Learn more in our article Dual Submersible Pump - For Eternity -

Dual Submersible Pump

(Patent pending ⁽¹⁾)

5/4/3/2 Inch ≤126 l/s (2,000 USGPM)
PN:SW5Dual-VA21B2345

Pump Information
Performance
Max Flow Rate:	≤ 126 l/s (2,000 USGPM)
Max Solid Diameter:	≤ 74 mm (2.9 inches)
Max Head:	≤34 m (112 ft)
Weight/Dimensions
Weight:	29 kg (64 lbs)
Pump Diameter:	500 mm (19.7 inches)
Pump Height:	400 mm (15.7 inches)
Top Features
Flexible Outlets in Dual Mode (2 hoses)	2/3/4/5 Inch
Flexible Outlets in Mono Mode (1 hose)	2/3/4/5 Inch
Suitable for Dirty Water	Yes
Dry Running 24/7	Yes
Maintenance-Free	Yes
Explosion-Proof	Yes
Max Medium Temperature	≤ 80°C (176°F)
Suction Operation	Yes
Free-Flow/Vortex	Yes
Optional Features
Ductile Iron	No
Atex (2014/34/EU: II 2G EX C IIA T6)	Yes
⁽¹⁾Patent Pending
Switzerland	CH000493 / 2023
Europe	24174242.8
USA	18/658,467

Graphics

Submersible Pump
5/4/3/2 Inch - ≤63 l/s (1,000 USGPM)

PN:SW5Mono-VA21B2345

Pump Information
Performance
Max Flow Rate:	≤ 63 l/s (1,000 USGPM)
Max Solid Diameter:	≤ 74 mm (2.9 inches)
Max Head:	26 m (85 ft)
Weight/Dimensions
Weight:	27.7 kg (61 lbs)
Pump Diameter:	500 mm (19.7 inches)
Pump Height:	400 mm (15.7 inches)
Top Features
Flexible Outlets in Mono Mode (1 hose)	2/3/4/5 Inch
Suitable for Dirty Water	Yes
Dry Running 24/7	Yes
Maintenance-Free	Yes
Explosion-Proof	Yes
Max Medium Temperature	≤ 80°C (176°F)
Suction Operation	Yes
Free-Flow/Vortex	Yes
Optional Features
Ductile Iron	Yes
Atex (2014/34/EU: II 2G EX C IIA T6)	Yes

Graphics

Image Sequences

5" Submersible Pump Image Sequence

Models

5" Submersible Pump Hydraulic, Gasoline, Electric, Diesel Models

Downloads

5" Submersible Pump Manuals, Parts Lists

Submersible Pump
3 Inch - ≤24 l/s (381 USGPM)

PN:SW3-VA14N

Pump Information
Performance
Max Flow Rate:	≤ 24 l/s (381 USGPM)
Max Solid Diameter:	≤ 63 mm (2.5 inches)
Max Head:	24 m (79 ft)
Weight/Dimensions
Weight:	11 kg (24 lbs)
Pump Diameter:	300 mm (11.8 inches)
Pump Height:	375 mm (14.8 inches)
Top Features
Suitable for Dirty Water	Yes
Dry Running 24/7	Yes
Maintenance-Free	Yes
Explosion-Proof	Yes
Max Medium Temperature	≤ 80°C (176°F)
Suction Operation	Yes
Free-Flow/Vortex	Yes
Optional Features
Ductile Iron	Yes
Atex (2014/34/EU: II 2G EX C IIA T6)	Yes

Graphics

Image Sequences

3" Submersible Pump Image Sequence

Models

3" Submersible Pump Hydraulic, Gasoline, Electric, Diesel Models

Downloads

3" Submersible Pump Manuals, Parts Lists

Submersible Pump
2 Inch - ≤13 l/s (206 USGPM)

PN:SW2-VA12N

Pump Information
Performance
Max Flow Rate:	≤ 13 l/s (206 USGPM)
Max Solid Diameter:	≤ 38 mm (1.5 inches)
Max Head:	34 m (112 ft)
Weight/Dimensions
Weight:	7.6 kg (17 lbs)
Pump Diameter:	238 mm (9.4 inches)
Pump Height:	330 mm (13 inches)
Top Features
Suitable for Dirty Water	Yes
Dry Running 24/7	Yes
Maintenance-Free	Yes
Explosion-Proof	Yes
Max Medium Temperature	≤ 80°C (176°F)
Suction Operation	Yes
Free-Flow/Vortex	Yes
Optional Features
Ductile Iron	Yes
Atex (2014/34/EU: II 2G EX C IIA T6)	Yes

Graphics

Image Sequences

2" Submersible Pump Image Sequence

Models

2" Submersible Pump Hydraulic, Gasoline, Electric, Diesel Models

Downloads

2" Submersible Pump Manuals, Parts Lists

Performance curve 5-inch dual submersible pumps

Performance curves 2, 3 and 4-inch submersible pumps

The Free-flow Technology

How It Works

The Grinding Function

Longer Operating Times

Utilizing Pump System Self-Dynamics Reduces Energy Costs

100% Wastewater Compatible

Grinding Function

Mixing Function

100% Maintenance-Free

Up to 80° Celsius (176°F)

100% Sludge Pump

Slurping Operation in Silent Mode

100% Electric Shock Protection

100% Dry-Running Capable

100% E-Check Free

100% Explosion-Proof

3" Submersible Pump 300 liters (79.25 gallons) in 3 seconds

Marti AG Employees on the 3" Submersible Pump

Marti AG Magazine

Why Does My Revenue Depend on the Engine Speed of My Hydraulic Unit?

Why Does My Revenue Depend on the Cooling Technology of My Hydraulic Unit?

FAQ - Technical

Difference between Mono and Dual Submersible Pumps

Oil Flow Optimization

Piping

Poor Performance (Diagram 1)

Good Performance (Diagram 2)

Better Performance (Diagram 3)

Best Performance (Diagram 4)

FAQ - Commercial

Cost Comparison: Dual vs. Mono Submersible Pump

Up to 15 years or more!

Dimensions and Weight of 2-Inch Submersible Pump

Dimensions and Weight of 3-Inch Submersible Pump

Dimensions and Weight of 4-Inch Submersible Pump

Dimensions and Weight of 5-Inch Dual Submersible Pump

12 l/s - 2" Tauchpumpe

12 l/s - 2" Tauchpumpe inkl. Ölmengenteiler für Direktanschluss an Bordhydraulik

9 l/s - 2" Tauchpumpe inkl. 6 PS Honda-54kg Hydraulikaggregat

11 l/s - 2" Tauchpumpe inkl. 9 PS Honda-68kg Hydraulikaggregat

11 l/s - 2" Tauchpumpe inkl. 13 PS Honda-81kg Hydraulikaggregat

12 l/s - 2" Tauchpumpe inkl. 18 PS Vanguard -105 kg Hydraulikaggregat

12 l/s - 2" Tauchpumpe inkl. 5,5kW 400V 16A-80kg Hydraulikaggregat

12 l/s - 2" Tauchpumpe inkl. 11kW 400V 16/32A-125kg Hydraulikaggregat

13 l/s - 2" Tauchpumpe inkl. 11kW 400V 16/32A -125kg Hydraulikaggregat

2" Tauchpumpe inkl. 13 PS Lombardini - 115kg Hydraulikaggregat

Grundwasser aus Graben abpumpen mit 2 Zoll Tauchpumpe ≤13l/s, 7,6 kg Gewicht

3 Zoll Tauchpumpe 800m Länge Kanalsanierung ≤24l/s bei 11kg Gewicht

3 Zoll Tauchpumpe Taucheinsatz technisches Hilfswerk THW ≤24l/s bei 11kg Gewicht

24 l/s - 3" Tauchpumpe

22 l/s - 3" Tauchpumpe inkl. Ölmengenteiler für Direktanschluss an Bordhydraulik

19 l/s - 3" Tauchpumpe inkl. 9 PS Honda-68kg Hydraulikaggregat

20 l/s - 3" Tauchpumpe inkl. 13 PS Honda-81kg Hydraulikaggregat

22 l/s - 3" Tauchpumpe inkl. 18 PS Vanguard -105 kg Hydraulikaggregat

20 l/s - 3" Tauchpumpe inkl. 5,5kW 400V 16A-80kg Hydraulikaggregat

22 l/s - 3" Tauchpumpe inkl. 11kW 400V 16/32A-125kg Hydraulikaggregat

24 l/s - 3" Tauchpumpe inkl. 11kW 400V 16/32A -125kg Hydraulikaggregat

20 l/s - 3" Tauchpumpe inkl. 13 PS Lombardini - 115kg Hydraulikaggregat

2-Inch Hydraulic Submersible Pump

Water Control Fretz Switzerland Sewer Rehabilitation NW600 Liner 4-Inch Dirty Water Pump ≤63 l/s, 27kg Weight

Sewer Rehabilitation Germany - Food Industry Water Management ≤ 70° Wastewater for Liner with 4-Inch Free-Flow Dirty Water Submersible Pump ≤63 l/s - 27 kg Weight

Sewer Rehabilitation Switzerland - Sewer Bypass with 4-Inch Submersible Pump

Fretz AG Water Management 210 l/s with HEPP2, three 5-inch dual submersible pumps, and one HEPP2 4-inch mono submersible pump in Basel

63 l/s - 4" Tauchpumpe

56 l/s - 4" Tauchpumpe inkl. Ölmengenteiler für Direktanschluss an Bordhydraulik

33 l/s - 4" Tauchpumpe inkl. 9 PS Honda-68kg Hydraulikaggregat

52 l/s - 4" Tauchpumpe inkl. 13 PS Honda-81kg Hydraulikaggregat

56 l/s - 4" Tauchpumpe inkl. 18 PS Vanguard -105 kg Hydraulikaggregat

36 l/s - 4" Tauchpumpe inkl. 5,5kW 400V 16A-80kg Hydraulikaggregat

56 l/s - 4" Tauchpumpe inkl. 18kW 400V 16/32A-125kg Hydraulikaggregat

63 l/s - 4" Tauchpumpe inkl. 11kW 400V 16/32A -125kg Hydraulikaggregat

52 l/s - 4" Tauchpumpe inkl. 13 PS Lombardini - 115kg Hydraulikaggregat

110 l/s (1700 US gpm) - 5" Dual Submersible Pump (Patent pending 1)

110 l/s (1700 US gpm) - 5" Dual Submersible Pump incl. Oil Flow Divider for Direct Connection to Onboard Hydraulics

110 l/s (1700 US gpm) - 5" Dual Submersible Pump incl. 23 HP YAMAHA - 150 kg (330 lbs) Hydraulic Unit

110 l/s (2906 US gpm) - 5" Dual Submersible Pump incl. 18kW 400V 32A - 180 kg (397 lbs) Hydraulic Unit incl. Float Control

3-Inch Hydraulic Submersible Pump

4-Inch Hydraulic Submersible Pump

110 l/s (1700 US gpm) - 5" Dual Submersible Pump (Patent pending ¹⁾

5-Inch Hydraulic Dual Submersible Pump (Patent Pending¹)

5/4/3/2 Inch ≤126 l/s (2,000 USGPM)
PN:SW5Dual-VA21B2345

Submersible Pump
5/4/3/2 Inch - ≤63 l/s (1,000 USGPM)

PN:SW5Mono-VA21B2345

Submersible Pump
3 Inch - ≤24 l/s (381 USGPM)

PN:SW3-VA14N

Submersible Pump
2 Inch - ≤13 l/s (206 USGPM)

PN:SW2-VA12N